ADS PS8 Especificações

WIL-10410-E-02 TO REPLACE WIL-10410-E-01Where Innovation Flowswww.wildenpump.comPS8Original™ SeriesMetal PumpEOMEngineeringOperation &Maintenance

WILDEN PUMP & ENGINEERING, LLC 8 WIL-10410-E-02Section 6SuggeSted InStallatIonWilden pumps are designed to meet the performance requirements of

WIL-10410-E-02 9 WILDEN PUMP & ENGINEERING, LLCNOTE: In the event of a power failure, the shut-off valve should be closed, if the restarting of

WILDEN PUMP & ENGINEERING, LLC 10 WIL-10410-E-02SuggeSted operatIon & MaIntenanceOPERATION: The Pro-Flo® SHIFT pumps are pre-lubricated and

Step 1Before starting disassembly, mark a line from each liquid chamber to its corresponding air chamber. This line will assist in proper alignment du

WILDEN PUMP & ENGINEERING, LLC 12 WIL-10410-E-02PUMP DISASSEMBLYStep 4Remove the discharge valve balls and valve seats from the liquid chambers

WIL-10410-E-02 13 WILDEN PUMP & ENGINEERING, LLCPUMP DISASSEMBLYStep 10Using two adjustable wrenches,turn the outer diaphragm pistons in a co

WILDEN PUMP & ENGINEERING, LLC 14 WIL-10410-E-02AIR VALVE / CENTER SECTION DISASSEMBLYTools Required:• Appropriate-sizedWrench• SnapRingPl

WIL-10410-E-02 15 WILDEN PUMP & ENGINEERING, LLCAIR VALVE / CENTER SECTION DISASSEMBLYStep 4Lift away air chamber from center section and remove

WILDEN PUMP & ENGINEERING, LLC 16 WIL-10410-E-02AIR VALVE / CENTER SECTION DISASSEMBLYStep 10Using an O-ring pick, removethe two (2) shaft

WIL-10410-E-02 17 WILDEN PUMP & ENGINEERING, LLCAIR VALVE / CENTER SECTION DISASSEMBLYStep 1Remove pilot exhaust muffler in pilot bleed port locat

Table of ConTenTsSection 1 CauTions—Read fiRsT! ...1Section 2 Wilden PumP designaTion sysTem ...

WILDEN PUMP & ENGINEERING, LLC 18 WIL-10410-E-02Figure ASHAFT SEALTAPEFigure BSHAFT SEALTAPENEEDLE NOSE PLIERSASSEMBLY:Upon performing applicabl

NOTES

Wilden PumP & engineering, llC 20 Wil-10410-e-02Section 8EXPLODED VIEW & PARTS LISTINGPS8 METALEXPLODED VIEWFULL FLOW PTFEALL CIRCLED PART I

Wil-10410-e-02 21 Wilden PumP & engineering, llCEXPLODED VIEW & PARTS LISTINGPS8 METALPARTS LISTING*See elastomer chart - Section 91 Air Va

Wilden PumP & engineering, llC 22 Wil-10410-e-02Section 9ELASTOMER OPTIONS1 Used in conjunction with metallic valve seat2 Elastomer option for u

NOTES

NOTES

Item # Serial # Company Where PurchasedCompany NameIndustryName TitleStreet AddressCity State Postal Code Country Telephone Fax E-mail Web Add

22069 Van Buren Street,Grand Terrace, CA 92313-5607Telephone: (909) 422-1731Fax: (909) 783-3440www.maag.comCopyright 2013, Pump Solutions Group (PSG

WIL-10410-E-02 1 WILDEN PUMP & ENGINEERING, LLC CAUTION: Do not apply compressed air to the exhaust port — pump will not function. CAUTION: D

Wilden PumP & engineering, llC 2 Wil-10410-e-02Section 2WILDEN PUMP DESIGNATION SYSTEMNOTE: Most elastomeric materials use colored dots for iden

WIL-10410-E-02 3 WILDEN PUMP & ENGINEERING, LLCSection 3how it works—pump The Wilden diaphragm pump is an air-operated, positive displacement, s

WILDEN PUMP & ENGINEERING, LLC 4 WIL-10410-E-02Section 4DIMENSIONAL DRAWINGSPS8 MetalPS8 Metal SanifloTMLW0022 REV. ADIMENSIONSITEM METRIC (mm)

Section 5PERFORMANCEFlow rates indicated on chart were determined by pumping water.For optimum life and performance, pumps should be specified so that

PERFORMANCEPS8 METAL FULL-STROKE PTFE-FITTEDFlow rates indicated on chart were determined by pumping water.For optimum life and performance, pumps sho

PS8 METAL SUCTION-LIFT CAPABILITYSuction-lift curves are calibrated for pumps operating at 305 m (1,000') above sea level. This chart is meant